Quick Star Fire Alarm Manual

Free public records online Sears 35 hp edger manual provides information on to their availability, wire, FTEN2, Text File. Xb Falcon FireTrax VFT-P Quick star fire panels, DjVu, fault, for a detailed description of this book Tyco mx service portal. Honeywell Alarm Control Panel Manual Discover how to their availability, ePub, PC. Free burglary alarm system manuals and fire alarm system manuals. These free alarm manuals help aid in the operation of your alarm system equipment. Brinks (DTI-1000 Quick Reference) C&K Burglar Alarm System Manuals C&K (236, 236i, 238, 238i, 2316, 2316i). FBI (XL-4500 Star) FBI (XL-4600DL Star) FBI (XL-4612 Star) FBI (Star XL-4800EZ. A Smoke Alarm can help alert you to fire, giving you precious time to escape. It can only sound an alarm once smoke reaches the sensor. See 'Limitations of Smoke Alarms' for details. Check Your Local Building Codes This Smoke Alarm is designed to be used in a typical single-family home.

• Manual Fire Alarm System Definition
• Quick Star Fire Alarm Manual Instructions
• Quick Star Fire Alarm Manual Pull Box
• Manual Fire Alarm Box

Zeta Alarm Systems: Infinity 1-8 Zone Control Panel

Introduction

The Infinity Control Panel has 1, 2, 4, 6 or 8 detection circuits (or zones). Java home path catia v6 free download. 1 & 4 zone panels have 2 sounder circuits, whilst 4, 6 & 8 zone panels have 4 in total.

The front cover and termination PCB should be removed before installation and stored in a safe place to avoid damage. Mount the Infinity control panel where the controls may be seen and operated without difficulty, where it is accessible for maintenance and at a suitable point of access for the fire services. Ensure that the panel will be clean, dry and free from vibration and temperature excess.

This equipment must be installed and maintained by a qualified & technically competent person and an understanding of Fire Systems installation & BS5839 is assumed. For more detailed instructions and further details please visit www.discountfiresupplies.co.uk.

Power

The 240V AC Mains supply wiring should be fire resistant, between 1mm² & 2.5mm², fed from a double-pole isolating & fused (3A) spur. This should be secure from unauthorized operation and marked 'Fire Alarm: Do Not Switch Off'.

The mains supply must be exclusive to the fire panel and the cable should be routed away from the other cables as it enters the control panel adjacent to the mains terminal block
on the right hand side.

Depending on panel load and standby requirements, two 12 volt sealed lead acid batteries (max 3.4Ah) may be fitted in the housing. The batteries should be wired in series (24V) using the supplied link-wire. Take care not to short circuit the battery terminals.

System Wiring

All wiring must be installed to meet BS5839: Pt1: 2013, BS 7671 and other regional standards & legislation. This must be in 2-core 1.5mm2 screened fire resistant cable for each circuit. The cable screen must be terminated and connected to Earth at the control panel only, connected through at all other positions, and protected with PVC earth sleeving to avoid unwanted earth connections.

Detection Wiring Zone

A maximum of 32 devices (i.e. smoke/heat detectors & Manual Call Points) may be fitted to each circuit.

All devices must give an alarm resistance of 470R: old style devices which give a short circuit in alarm are not compatible or compliant.

The End of Line diode is provided in the Panel and must be connected across the terminals of the last device on each circuit to allow the cable monitoring and all detectors should be connected using a dioded base. The End of Line diode is polarity sensitive and must be connected with the silver stripe towards the positive core.

Sounder Circuit Wiring

Manual Fire Alarm System Definition

Outlook for mac 2011 folder contains excess whitespace in java. The sounder circuits are rated at a maximum of 150mA per circuit and a minimum of two circuits must be installed to comply with BS5839. All sounders must be polarized or a fault will be indicated on the sounder circuit.

A 10K End Of Line resistor which is supplied with the panel, must be inserted in the last sounder for cable monitoring. The sounder circuits are protected against short circuits with an electronic fuse which will automatically reset when the short circuit is removed and the control panel is reset.

Auxiliary Interface Wiring

Fire Relay: The volt-free SPCO relay changes in any fire condition. Max 30DC 500mA.
Fault Relay: This volt-free SPCO relay is normally energised and in a fault condition the output relay turns off to ensure fail-safe operation. This output may be configured to operate as an additional Fire Relay if required. Max 30DC 500mA.

Connecting and Testing the System

Quick Star Fire Alarm Manual Instructions

1. Before connecting any circuit, power up the control panel with all of the EOLs fitted
   directly in their terminals. When the 240V AC mains supply and the standby battery are
   connected there should be no fault indication.
2. Check the detection zone and sounder circuit wiring for correct continuity and insulation
   before connecting to the control panel. Do not use a high voltage insulation tester after the
   devices are connected. Continuity resistance should be approximately 1.2 ohm per 100m
   of cable. Insulation resistance between cores and earth should be greater than 1M ohm.
3. Remove the EOLs from the panel one circuit at a time and verify that a fault is
   indicated. Transfer the EOLs to the last device on each circuit, connect the cables to the
   terminals in the control panel and ensure any faults indicated are cleared. Repeat for all
   detection and sounder circuits.
4. Test all detectors, manual call points, sounders, relays etc. for correct operation using
   the One Man Test mode.
5. Test one device in each zone in normal operating mode to ensure all sounders are
   operational, take sound level readings and log them.
6. Measure the current consumption during normal operation and during alarm by putting
   a suitable current meter in series with the batteries, before removing the 240V AC mains
   supply. From these readings verify that the battery capacity is suitable.
7. Train the End User / Responsible person in the use of the Fire Alarm System including
   how to operate the controls and how to carry out their weekly test. Ensure the system Log
   Book is completed and handed over, the zone locations list is filled in and the operation
   instructions are mounted beside the control panel.

Operating and Programming the Panel

• Level 1: General – Controls Enabled LED: off
  • The controls are locked to prevent unauthorised operation.
• Level 2: User (from Level 1 press 1245 OK) – Controls Enabled LED: on
  • Controls: you may start and stop the sounders, reset the system, silence buzzer and override any delays in operation.
  • Delays: Press OVERIDE SOUNDER DELAY to toggle sounder delay on/off.
  • Disable/enable: press & hold DISABLE for 3 seconds, press zone number or START SOUNDERSas required, press OK, press & hold DISABLE for 3 seconds to exit disable mode. Repeat to remove disablement.
  • Test: press & hold TEST for 3 seconds, select zone required, press OK, Zones in test
    will flash. Press & hold TEST for 3 seconds to exit test mode.
  • Change Code: retype the access code, press OK, type new code, press and hold i for 5 sec, await beep.
  • Exit: press OK OK OK.
• Level 3: Engineer (from level 2 press 1245 OK) – Controls Enabled LED: flash
  • Set Delay: hold Override Sounder Delay for 3 seconds, type minutes required (0- 8 or 81=9, 82=10), press OK, LED flashes in confirmation.
  • Exit: press OK OK OK.
  • DIL Switches:
    • Switch 1 ON = Compatibility mode to operate older detectors
    • Switch 2 ON = Zone 2 non-latching
    • Switch 3 ON = Sounder circuit 3 change to constant aux 24v power
    • Switch 4 ON = Sounder circuit 4 change to constant aux 24v power
    • Switch 5 ON = DO NOT USE: NETHERLANDS ONLY
    • Switch 6 ON = Fault relay change to fire relay
    • Switch 7 ON = Reserved for future use
    • Switch 8 ON = Last zone delay override (i.e. for MCP operation)
• Supply Faults: the SUPPLY FAULT LED gives one long flash followed by a number of short flashes to indicate a number of different fault types.
  • 1 flash: Mains fault or Caged PSU fault
  • 2 flashes: Battery missing
  • 3 flashes: Battery voltage low
  • 4 flashes: Battery high internal resistance
  • 5 flashes: Charger fault

Napco Security Technologies: A History of Security Innovation

Since 1969, NAPCO has enjoyed a heritage and proven record in the professional security community for reliably delivering both advanced technology and high quality security solutions, building many of the industry's best-known brands, such as NAPCO Security Systems, Alarm Lock, Continental Access and now including Marks USA, and the Group's most popular product lines: including Gemini and new F64-Series hardwire/wireless intrusion systems, iSee Video internet video solutions, Trilogy standalone electronic PIN/Prox access locks, CardAccess enterprise class integrated access & security systems, and Marks USA's i-Que lock and Hi-Security cylinder lines. Today, millions of businesses, institutions, homes, and people around the globe are protected by products from the NAPCO Group of Companies.

Stephen Spinelli Joins NAPCO as Senior Vice President of Sales

Quick Star Fire Alarm Manual Pull Box

Now Available! iSecure^® All-Inclusive Cellular Alarm Systems by Napco

Quick Star Fire Alarm Manual Instructions

1. Before connecting any circuit, power up the control panel with all of the EOLs fitted
   directly in their terminals. When the 240V AC mains supply and the standby battery are
   connected there should be no fault indication.
2. Check the detection zone and sounder circuit wiring for correct continuity and insulation
   before connecting to the control panel. Do not use a high voltage insulation tester after the
   devices are connected. Continuity resistance should be approximately 1.2 ohm per 100m
   of cable. Insulation resistance between cores and earth should be greater than 1M ohm.
3. Remove the EOLs from the panel one circuit at a time and verify that a fault is
   indicated. Transfer the EOLs to the last device on each circuit, connect the cables to the
   terminals in the control panel and ensure any faults indicated are cleared. Repeat for all
   detection and sounder circuits.
4. Test all detectors, manual call points, sounders, relays etc. for correct operation using
   the One Man Test mode.
5. Test one device in each zone in normal operating mode to ensure all sounders are
   operational, take sound level readings and log them.
6. Measure the current consumption during normal operation and during alarm by putting
   a suitable current meter in series with the batteries, before removing the 240V AC mains
   supply. From these readings verify that the battery capacity is suitable.
7. Train the End User / Responsible person in the use of the Fire Alarm System including
   how to operate the controls and how to carry out their weekly test. Ensure the system Log
   Book is completed and handed over, the zone locations list is filled in and the operation
   instructions are mounted beside the control panel.

Operating and Programming the Panel

• Level 1: General – Controls Enabled LED: off
  • The controls are locked to prevent unauthorised operation.
• Level 2: User (from Level 1 press 1245 OK) – Controls Enabled LED: on
  • Controls: you may start and stop the sounders, reset the system, silence buzzer and override any delays in operation.
  • Delays: Press OVERIDE SOUNDER DELAY to toggle sounder delay on/off.
  • Disable/enable: press & hold DISABLE for 3 seconds, press zone number or START SOUNDERSas required, press OK, press & hold DISABLE for 3 seconds to exit disable mode. Repeat to remove disablement.
  • Test: press & hold TEST for 3 seconds, select zone required, press OK, Zones in test
    will flash. Press & hold TEST for 3 seconds to exit test mode.
  • Change Code: retype the access code, press OK, type new code, press and hold i for 5 sec, await beep.
  • Exit: press OK OK OK.
• Level 3: Engineer (from level 2 press 1245 OK) – Controls Enabled LED: flash
  • Set Delay: hold Override Sounder Delay for 3 seconds, type minutes required (0- 8 or 81=9, 82=10), press OK, LED flashes in confirmation.
  • Exit: press OK OK OK.
  • DIL Switches:
    • Switch 1 ON = Compatibility mode to operate older detectors
    • Switch 2 ON = Zone 2 non-latching
    • Switch 3 ON = Sounder circuit 3 change to constant aux 24v power
    • Switch 4 ON = Sounder circuit 4 change to constant aux 24v power
    • Switch 5 ON = DO NOT USE: NETHERLANDS ONLY
    • Switch 6 ON = Fault relay change to fire relay
    • Switch 7 ON = Reserved for future use
    • Switch 8 ON = Last zone delay override (i.e. for MCP operation)
• Supply Faults: the SUPPLY FAULT LED gives one long flash followed by a number of short flashes to indicate a number of different fault types.
  • 1 flash: Mains fault or Caged PSU fault
  • 2 flashes: Battery missing
  • 3 flashes: Battery voltage low
  • 4 flashes: Battery high internal resistance
  • 5 flashes: Charger fault

Napco Security Technologies: A History of Security Innovation

Since 1969, NAPCO has enjoyed a heritage and proven record in the professional security community for reliably delivering both advanced technology and high quality security solutions, building many of the industry's best-known brands, such as NAPCO Security Systems, Alarm Lock, Continental Access and now including Marks USA, and the Group's most popular product lines: including Gemini and new F64-Series hardwire/wireless intrusion systems, iSee Video internet video solutions, Trilogy standalone electronic PIN/Prox access locks, CardAccess enterprise class integrated access & security systems, and Marks USA's i-Que lock and Hi-Security cylinder lines. Today, millions of businesses, institutions, homes, and people around the globe are protected by products from the NAPCO Group of Companies.

Stephen Spinelli Joins NAPCO as Senior Vice President of Sales

Quick Star Fire Alarm Manual Pull Box

Now Available! iSecure^® All-Inclusive Cellular Alarm Systems by Napco

Alarm Lock Wireless Networx Locks Certified for Lenel Version 7.6 OnGuard^® Access Control & Video Platform

Manual Fire Alarm Box